Sense360 Firmware Configuration Tool

Step 1: Configure Core Features

Core Type

Select your Sense360 core hardware variant.

Core

Standard Sense360 core module without voice hardware.

Core Voice

Core with I2S microphone array and audio output for voice control. Requires Rev B core or newer, J5 audio interface header.

Step 2: Where is this unit being installed?

Quick start:

Or configure step-by-step below

Wall Mount

Standard wall installation with full module support

Ceiling Mount

Ceiling installation

Step 3: Select Power Option

USB Power

Standard USB-C power connection

POE Module

Power over Ethernet module

PWR Module

External power module

Step 4: Add Expansion Modules

Select a mounting and power option to see supported expansion modules.

AirIQ Module

Selected: AirIQ None

Air quality stack for particulate, VOC, and CO₂ sensors.

Core: No additional requirement
Headers: No additional headers

Base

Balanced air quality sensing with VOC, CO₂, and particulate coverage.

Core: Rev B core or newer
Headers: J4 sensor bus · J7 auxiliary power

Fan Analog Bathroom AirIQ

Pro

Full particulate insights plus advanced gas and flow monitoring.

Core: Rev C core or newer
Headers: J4 sensor bus · J6 particulate harness · J7 auxiliary power

Fan Analog Presence Pro Bathroom AirIQ

Bathroom AirIQ Module

Selected: Bathroom AirIQ None

Ceiling-mounted air quality sensors optimized for bathroom environments.

None

Core only, no Bathroom AirIQ sensors.

Core: No additional requirement
Headers: No additional headers

Base

Humidity, temperature, and air quality monitoring optimized for bathroom environments.

Core: Rev B core or newer
Headers: J4 sensor bus · J7 auxiliary power

AirIQ Base/Pro

Presence Module

Selected: Presence None

mmWave radar options for occupancy detection.

Core: No additional requirement
Headers: No additional headers

Base

Single-zone mmWave radar coverage.

Core: Rev B core or newer
Headers: J2 radar slot

Pro

Dual-zone radar with LD2450 secondary coverage.

Core: Rev D core
Headers: J2 radar slot · J8 secondary UART

AirIQ Pro

Comfort Module

Selected: Comfort None

Environmental sensing for comfort tuning.

Core: No additional requirement
Headers: No additional headers

Base

Humidity and ambient light monitoring.

Core: Rev A core or newer
Headers: J3 environmental header

Fan Module

Selected: Fan None

Output driver choices for external fan control.

Core: No additional requirement
Headers: No additional headers

PWM

Variable speed fan control via PWM driver.

Core: Rev A core or newer
Headers: J9 PWM driver

Analog

0–10V analog fan control with isolation harness.

Core: Rev C core or newer
Headers: J4 analog DAC · J10 isolation harness

AirIQ Base/Pro

LED Ring

Selected: LED Ring None

Visual feedback ring with optional microphone integration for voice-enabled cores.

Core: No additional requirement
Headers: No additional headers

Core Voice

Base

Addressable RGB LED ring for visual status feedback.

Core: Rev A core or newer
Headers: J11 LED data · J12 LED power

Bathroom AirIQ Module

Selected: Bathroom AirIQ None

Bathroom-optimized air quality sensing with humidity, pressure, VOC/NOx, and optional condensation detection.

None

Bathroom configuration without AirIQ sensors.

Core: No additional requirement
Headers: No additional headers

Base

Humidity, pressure, and VOC/NOx sensing for bathroom environments.

Core: To be added
Headers: To be added
Sensors: SHT4x (temp/humidity) · BMP390 (pressure) · SGP41 (VOC/NOx)

Pro

Full sensor suite with IR surface temperature, condensation risk detection, and particulate monitoring.

Core: To be added
Headers: To be added
Sensors: SHT4x · BMP390 · SGP41 · MLX90614 (IR/condensation) · SPS30 (PM1.0/2.5/10)

Highlight a module option to see required core revisions, headers, and conflicts.

Step 5: Review & Install

Use desktop Chrome or Edge to connect your Sense360 hub. Then click ‘Install firmware’. If you’re not on a supported browser, download the .bin instead.

Your selections

Verify the Sense360 hub is powered and connected to your computer.
Keep this browser tab open until the flashing process finishes.
Do not disconnect power/USB during flashing.

I understand and will keep the hub powered and connected throughout flashing.

Compatible Firmware

After the install finishes, keep the hub powered on and connected to the same network as Home Assistant. Discovery usually happens within a minute. If the device doesn’t appear, open the integrations dashboard and follow the ESPHome adoption steps to add it manually.

Sense360 Firmware Configuration Tool

Step 1: Configure Core Features

Core Type

Step 2: Where is this unit being installed?

Step 3: Select Power Option

Step 4: Add Expansion Modules

AirIQ Module

Bathroom AirIQ Module

Presence Module

Comfort Module

Fan Module

LED Ring

Bathroom AirIQ Module

Step 5: Review & Install

Your selections

Before you flash

Compatible Firmware

Your configuration

Why choose it

Keep in mind

Measurements & advanced notes

Browser Not Supported